XH-1500 and FX-520 Rotary Cutters
After our company switched to Schulte, our revenue per cutter went up 33%. We were getting paid by the acre so we were always worried about production and cost per acre. We were having problems with competitive cutters. We tried the Schulte cutters and it didn’t take us long to figure out that it was the cutter we wanted. We didn’t realize how bad our previous cutters were until we put a Schulte on the ground. We think the Schulte cuts better period. It’s unbelievable the quality of cut that we can get at what we would call a high rate of mowing speed. We get paid by the acre so productivity is a big deal for us, ground speed is a big deal for us.
Roman Albert Owner of Lot Maintenance of Oklahoma Inc., Tulsa OK
XH-1500 Rotary Cutters
“We’ve found a mower that will stand the test of time, without a doubt the best mower we’ve ever had. We’ve been in business since 1983, we bought four Schulte mowers in ‘94 and a couple more in ‘97 and before we knew it they were all green, we didn’t have any more red ones or yellow ones. The biggest thing we’ve found with Schulte over the competition we used prior to ‘94 is we didn’t have to get the service truck out to the mow route every day when they’d be down for an hour or two once a week on average, if not more. When you’re out on the highway getting paid by the job not the hour, you’re not making money when they’re sitting still. The series three has been almost bullet proof, that’s on highway mowing you know, running 100 pound semi recaps and drive line knuckles through them. I’ve hit three bowling balls in my career, we test them out. I like to give credit where credit is due, you guys have a good product.”
Kelly Hall C & H Mowing, Hebron, IN
"Keeping the tractor out of the ditch reduces cuts and flats on the tractor tire and less tractor maintenance with the tractor running level. We can cut much closer to sloughs in wet years, no more getting stuck, no ruts in ditches to bounce over the next year. We haven't rolled a tractor since we have started using the Schulte Flex Arm. When cutting brush the tractor is in the open and away from the trees. The operator can see what he is doing much better. We also use the Flex Arm when we are doing our back cut. We never unhook. Our new series 3 XH1500 is working very good. We can cut around 5 miles an hour."
Ken Stockburger R.M of LeRoy, LeRoy, SK
5026 Rotary Cutter
"I'm a rancher with a lot of mowing to do. When its time to mow, I need to go. Maintenance and downtime was something we always had with batwing rotary cutters. We purchased a Schulte 5026 26 ft. batwing mower 2 years ago. This cutter has been over a lot of acres and our down time and maintenance has only included 2 flat tires and greasing. We like Schulte mowers and have recently purchased a XH1500 Series 3 15 ft. cutter. We highly recommend Schulte mowers. They are just plain dependable."
Bill Inhofe Rancher, Muskogee, OK USA
5026 Rotary Cutter
"Our bean crop yielded 160lbs per acre more because of crop residue management using the Schulte 5026 rotary cutter. In the Spring, where we had done the mowing, the ground warmed up faster, the beans came out of the ground faster and they grew better. Where it hadn't been mowed we had a lower yield and higher disease. The fields that hadn't been mowed are the ones we planted first and the beans which we planted last (where we mowed), within a couple of weeks, they were at the same stage as the earlier planted fields. When we cultivated In the fall we could do a good job of weed control and get right up to the beans on the fields we mowed, as trash and residue was cleared. We didn't have a whole lot of mould on the beans, but where we did find it, it was in the fields that weren't mowed. We also found we could till and seed quicker on fields we mowed."
John Crooymans Farmer, Bow Island, AB
XH1500 Series III
"We are a commercial mowing business. We purchased a Schulte XH1500 Series 3 15ft. batwing mower this year. In 500 hours of use we have replaced the blades and a set of wing skids once. Blades on our other mowers rarely lasted 100 hours. It takes 2 1/2 hours to change a set of blades. Parts are an expense as well as down time. Our business is mowing not fixing. With our Schulte, our main cost is greasing. The Schulte is a level mowing, smooth running machine. Our employees prefer operating the Schulte. We feel it is worth its cost and would recommend Schulte to anyone."
Larry Rindels Commercial Cutter, Tulsa, OK
“With the wet conditions in 2005 and 2006 most of our ditches couldn’t have been cut without the Schulte Flex Arm. I have seen reduced tire maintenance on our tractor with the use of the Flex Arm. Our operator fatigue has been greatly reduced with the use of the Schulte Flex Arm. A Lot of our roads could not be cut without the Flex Arm because of wet and steep slopes. The Schulte Flex Arm is worth its weight in gold.”
Lawrence Knittig R.M of St. Peter, Annehiem, SK
"The Schulte FX-180 performs great in all conditions. It has replaced some of my older mowers and handles all mowing conditions I can throw at it. It runs smooth with its 7ga spun formed stump jumpers and the 7ga domed deck sheds water and is easy to keep clean. This single domed deck ads extra room under the deck area for a noticeably improved and increased cut rate over my old mowers. I would recommend this Schulte mower to anyone looking at an extremely tough, fast/clean cutting and smooth running Flex Wing Mower. Schulte is a cut above the rest!"
Jim Shipley Farmer, Lake Worth, FL
XH1500 Series III
"Our operators like the smoothness of operating the Schulte XH1500 Series 3. Decks stay cleaner than other mowers. Our previous 15ft mowers experienced a lot of down time after 2 years of service. Down time kills us. We look for may years of service from our Schulte rotary cutter.
Danny Holt Custom Cutter, Greer County, OK
XH1500 Series III
"I am extremely pleased with the Schulte XH1500 III cutter. I cut water levy's around the Everglades in Florida and have put this Schulte mower through it's paces. It has never let me down and and out performs any cutter have ever used before. The quality and strength of this cutter is second to none. I can cut faster with the deep deck and the domed deck keeps the mower clean and free of water which is important in Florida. I highly recomend a Schulte XH1500 III to any one looking for a top quality mower."
John Pellicone Mower Operator, West Palm Beach, FL
“I can travel at least 1 mile an hour faster than I could travel with the series 2 cutter. I like the Easy to clean the deck. I Have used the Flex-arm for 4 years. If I had to go back to cutting without the Flex-arm I would not be operating the cutter.”
Rob Hulgan R.M of Kindersley, Kindersley, SK
XH15000 Series III
“I love the clean top single domed deck. It stays clean and sheds water perfectly. The heavy duty gearboxes have worked flawlessly. No problems at all and they run very cool. The new low maintenance drive lines are great. Less time servicing and more time making money cutting. The 17.5” lift height means I don’t scalp when going over approaches and reduces blade wear from ground to blade contact. I have recently put on some Equal Angle Hitches on 3 of my Schulte XH1500 cutters and they are working beautifully. No heavy CV shaft to hook up. The increased depth of the body of the cutter allows material to feed in the front better and flow through better. I have increased my ground speed by over 1 mile per hour over my previous model. Chain guards will be easy to maintain with the slide through rod design. A great improvement! The centralized rear suspension makes for a stabile and smooth ride when transporting from location to location. I really like the Schulte Super Suction blades in combination with this cutter. They really suck up the tractor tracks, even in heavy wet grass. I run tractors in the 105 - 115 HP range and the Schulte cutters have worked great with my tractors.”
Ken Singelton Mower Operator, Kennedy, SK
5026 Rotary Cutter
"We are a 5000 acre Texas South Plain cotton farm. We purchased a Schulte 5026 rotary cutter 5 years ago. All of our cotton acres are shredded annually plus we mow a lot of CRP. Shredded or mowed material is evenly distributed. The machine has more than exceeded our expectations. Maintenance on our Schulte is minimal; a set of blades lasts well through a season. The Schulte 5026 is very operator friendly, which makes it easy for any of our operators to run the machine."
Theadore Wells Cotton Farmer, Stanton, TX
7400 3pt Hitch
"We have small snow removal business in South Lake Tahoe, CA. This is our first Winter using your blower. Your equipment has really increased our capabilities. We now do twice the work with half the effort."
John Chenoweth Snow Removal Contractors, South Lake Tahoe, CA
FX520 Rotary Mowers
"Cat Challengers operating with the FX520 mowers. This combination works fantastic for us"
Mark Yanke Mower Operator, Churchbridge, SK
PO Box 70
PHONE: (306) 287-3715
FAX: (306) 287-3355